
Original Link: https://www.anandtech.com/show/3429
We just reviewed the CyberPower Gamer Xtreme XI system with a 4.0GHz QX9770 and SLI GTX 280s that comes in an NZXT Khaos case. We thought it would be good to provide a separate look at the case since it has some cool features and looks quite nice. The Khaos case has been available for several weeks now. It is a full-tower offering a lot of space, with five 5.25" drive bays and eight 3.5" drive bays for hard drives. The front has two large 120mm fans preinstalled. In the top-back are two additional 120mm fans that will provide additional airflow to the CPU area, one venting upwards and the other blowing out the back.
Two of the 5.25" drive bays have faceplates that cover your installed optical drives. Looking at the rear, we see two small openings where the tubes of an external water-cooling device can enter/exit. At the bottom are two mounting areas for power supplies. As we noted in the CyberPower review, users can install two power supplies. NZXT also delivers a Y-cable so user can run both power supplies off of one wall socket. There are two wheels at the front of the chassis while the back has two rubber stoppers that keep the case in place. To move the case you lift up the handle at the back and wheel it around. (Mind your fingers, though.)
Internals
The inside looks like a standard ATX full-tower, but there are a few extras. The motherboard fits in the upper-left section and the power supplies as mentioned are at the bottom. Hard drives, optical drives, and anything else that uses the 3.5"/5.25" bays is at the front of the case, as usual. Between the drive bays and the motherboard is a small bracket where users can choose to mount three additional 120mm fans. There are two hard drive cages, each capable of holding up to four hard drives. Each of the drive cages has a 120mm fan preinstalled, so completely filling a cage and making a hard drive sandwich shouldn't cause any temperature concerns. If you want to remove the drive cages, you will need to take off the front bezel first. Motherboard installation on the other hand is made easier by the inclusion of a motherboard tray that can swing out with the removal of a few screws.
Installation
It's very easy to install all the components into this case. The motherboard tray helps users with the installation of the motherboard, graphics card(s), and additional expansion cards. However, it's worth nothing that certain larger CPU coolers may make it difficult or impossible to open the motherboard tray, in which case you would have to install component the old-fashioned way. Our Xigmatek HDT-S1283 that's around 6 inches tall couldn't fit through the opening when we tried to move the tray back into position. We were lucky since we could just remove a little plate to pass the cooler through, but wider/taller coolers will have problems - anything taller than around 6 inches will need to be installed after the motherboard is locked into its final position. There not much space between the bracket for the three additional 120mm fans, so we recommend removing it if you aren't planning to install these fans. Above the power supply is a square opening that was large enough even for all that cables for our triple-SLI setup. This helps keep the cables clean and out of the way. However, after we closed both sides of the case, we noticed that the mass of cables pushed against the right side and created a little gap between the case and side panel. A modular PSU (or PSUs) could help here, as you wouldn't have as many extra cables tucked into a small area.
Quick Thoughts
NZXT gets this case from the same factory where Hiper produces their Anubis and Osiris cases. The factory is located in Dongguan, China, and in fact I just visited this factory six months ago when we were invited to look at this and SevenTeam's power supplies factory. The build quality is very good and there is little negative to discuss. The only problem we encountered with our case is that the wheels at the front were a little damaged - we couldn't roll the case because the left wheel got jammed against the plate above it. NZXT should strengthen the base of the wheels a little more to prevent this problem from occurring. There are also ridges like you would find on a heatsink on the top and bottom of the case, but they are simply for appearance and don't really help improve cooling performance. Finally, the fans on the front, top, and back panels are clearly audible, and if you run multiple GPUs you will end up with a noisy system. The Khaos case has a lot of good elements, but the price starts at $399 and around €399 in Europe, which is quite high. A case like this is a long-term investment and some will be willing to pay the price of entry, though we can only hope prices will come down to a more affordable range.